Siemens SIPART PS100 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 54

background image

Service and maintenance

8

8.1

Basic safety notes

8.1.1

Maintenance

The device is maintenance-free. However, a periodic inspection according to pertinent directives
and regulations must be carried out.

An inspection can include, for example, check of:

• Ambient conditions

• Seal integrity of the process connections, cable entries, and cover

• Reliability of power supply, lightning protection, and grounds

WARNING

Dust layers above 5 mm

Risk of explosion in hazardous areas.

Device may overheat due to dust build up.
• Remove dust layers in excess of 5 mm.

NOTICE
Penetration of moisture into the device

Damage to device.
• Make sure when carrying out cleaning and maintenance work that no moisture penetrates

the inside of the device.

8.2

Cleaning

Cleaning the enclosure

• Clean the outside of the enclosure with the inscriptions and the display window using a cloth

moistened with water or a mild detergent.

• Do not use any aggressive cleansing agents or solvents, e.g. acetone. Plastic parts or the

painted surface could be damaged. The inscriptions could become unreadable.

SIPART PS100
Compact Operating Instructions, 05/2021, A5E50188940-AA

39

«
...
37
38
39
40
41
...
»

Содержание SIPART PS100























































Отзывы:

Нет отзывов

Похожие инструкции для SIPART PS100

1436 cPos Profinet

Бренд: Gemu Страницы: 29

Бренд: Samson Страницы: 80

Бренд: HART Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды