Siemens SINUMERIK ONE NCU 1740 Скачать руководство пользователя

Страница: 55 / 164

Interface overview

Table 8-1

Overview of the interfaces that can be used

Interface

Designation

Connector type

DRIVE-CLiQ

X100 - X103

Spec. RJ45 socket

Digital inputs/outputs

X122, X132, X142

3x14-pole spring-loaded terminals

24 VDC power supply

X124

Screw-type terminals, 4-pin

PROFINET

X150; port 1, 2
X160; port 1

Standard RJ45 socket

Ethernet IE1/OP

X120

Standard RJ45 socket, not suitable for
PoE

Ethernet IE2/NET

X130

Standard RJ45 socket, not suitable for
PoE

PROFIBUS DP1

X126

9-pin SUB-D socket

USB

X125, X135

Double SuperSpeed, type A socket

Ethernet (service socket)

X127

Standard RJ45 socket, not suitable for
PoE

SD card

X55

SD standard slot

Service socket

X140

DisplayPort socket

Note

Interface X140 is only designed for service purposes, and cannot be used to connect a display.

8.2

Communication services and used port numbers

SINUMERIK supports the protocols listed in the following tables. The address parameters, the
relevant communication layer as well as the communication role and the communication
direction are specified for each protocol.

This information allows you to match the security measures for the protection of the automation
system to the used protocols (e.g. firewall).

The following table shows a section of the various layers and protocols that are used.

Connecting

8.2 Communication services and used port numbers

NCU 1740
Equipment Manual, 10/2021, A5E51087503B AA

Содержание SINUMERIK ONE NCU 1740





































































































































































Результаты поиска

Содержание SINUMERIK ONE NCU 1740

Отзывы:

Похожие инструкции для SINUMERIK ONE NCU 1740

Бренды по названию

Популярные бренды

Siemens SINUMERIK ONE NCU 1740, Руководство по эксплуатации оборудования

Результаты поиска

Содержание SINUMERIK ONE NCU 1740

Отзывы:

Похожие инструкции для SINUMERIK ONE NCU 1740

Бренды по названию

Популярные бренды