Siemens SINUMERIK MCU1720 Скачать руководство пользователя страница 83

Страница: 83 / 102

Service and maintenance

Cleaning the device

The device is designed for maintenance-free operation. Nevertheless, you may have to clean

the device.

Note
Switch the device off for cleaning
Clean the device only when it is switched off.

For cleaning, use a soft cloth moistened either with water or a mild cleaning agent. Use only

dishwashing detergent or foaming detergent.

Procedure
Spray the cleaning agent on to a cleaning cloth. Never use caustic solvents or abrasive

cleaners.

Note
Avoid damage
Do not clean the device using compressed air or steam jets because they can damage it.

Checking the device

In order to prevent foreign bodies or liquids entering the device, regularly check the device for

the following:
● Ensure that all the housing screws are in place and tight
● For damage to the housing
● For damage to the cable cover or cable entry

Protect the device from environmental effects

Protect the device against the following environmental factors:
● Direct sunshine and heat sources
● Mechanical vibration and shock
● Dust
● Humidity
● Strong magnetic fields

MCU 1720

Equipment Manual, 09/2019, A5E47437728B AB

Содержание SINUMERIK MCU1720







































































































Результаты поиска

Содержание SINUMERIK MCU1720

Отзывы:

Похожие инструкции для SINUMERIK MCU1720

Бренды по названию

Популярные бренды

Siemens SINUMERIK MCU1720, Руководство по эксплуатации оборудования

Результаты поиска

Содержание SINUMERIK MCU1720

Отзывы:

Похожие инструкции для SINUMERIK MCU1720

Бренды по названию

Популярные бренды