Siemens SINUMERIK MCU1720 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 102

Siemens SINUMERIK MCU1720 Скачать руководство пользователя страница 48

6. Please inform the delivery service immediately if the package contents are incomplete or

damaged or do not correspond with your order. Fax the enclosed form "SIMATIC IPC/PG

Quality Control Report".

WARNING

Electric shock and fire hazard due to damaged device
A damaged device can be under hazardous voltage and trigger a fire in the machine or

plant. A damaged device has unpredictable properties and states.
Death or serious injury could occur.
Make sure that the damaged device is not inadvertently installed and put into operation.

Label the damaged device and keep it locked away. Send off the device for immediate

repair.

NOTICE
Damage from condensation
If the device is subjected to low temperatures or extreme fluctuations in temperature during

transportation, as is the case in cold weather, for example, moisture can build up on or

inside the device (condensation).
Moisture causes a short circuit in electrical circuits and damages the device.
In order to prevent damage to the device, proceed as follows:
● Store the device in a dry place.
● Bring the device to room temperature before starting it up.
● Do not expose the device to direct heat radiation from a heating device.
● If condensation develops, wait approximately 12 hours or until the device is completely

dry before switching it on.

7. Please keep the enclosed documentation in a safe place. It belongs to the device. You need

the documentation when you commission the device for the first time.

8. Write down the identification data of the device.

7.2.2

Identification data of the device

Unpacking the device

The device can be identified uniquely with the help of these numbers in case of repairs or theft.
Enter the identification data in the table below:

Identification date

Source

Value

Article number

S VP________

Serial number

6FC5222-__________

Installation
7.2 Preparing for installation

MCU 1720

48

Equipment Manual, 09/2019, A5E47437728B AB

«
...
46
47
48
49
50
...
»

Содержание SINUMERIK MCU1720







































































































Отзывы:

Нет отзывов