Siemens SINAMICS S220 Скачать руководство пользователя страница 98 | Manualshive

Страница: 98 / 156

Siemens SINAMICS S220 Скачать руководство пользователя страница 98

6.2.2

Shield connection plate and terminal

6.2.2.1

Option for the shielding

You can use one of the following two methods for connecting the shield:

• Connect the cable to the strain relief plate using a hose clamp.

• Use the optional shield connection plate in combination with a shield connection clamp. This

provides for improved contacting and makes it easier to connect the shield.

①

②

③

Strain relief plate (included in the scope of supply)
Optional shield connection plate (6SL5166-1BD00-0AA0)
Shield connection clamp (8WH9130-0NA00 (Phoenix SK28) or 8WH9130-0PA00 (Phoenix
SK35))

The optional shield connection plate, the shield connection clamps and the hose clamp are not
included in the scope of supply of the Smart Line Module.

Note

Only use shielded connecting cables with the optional shield connection plate and the shield
connection clamp.

Accessories
6.2 Accessories for Smart Line Modules

Booksize power units

96

Equipment Manual, 01/2022, 6SL3097-6AC30-0BP0

«
...
96
97
98
99
100
...
»

Содержание SINAMICS S220





























































































































































Отзывы:

Нет отзывов