Siemens SINAMICS S220 Скачать руководство пользователя страница 62

Страница: 62 / 156

X1: Line connection

Termi‐
nal

Function

Technical specifications

Connectable cable cross-
sections

Flexible
With end sleeve, without plastic sleeve
With end sleeve, with plastic sleeve
AWG / kcmil

6 … 16 mm

10 ... 6

Stripped length

12 mm (0.47 inch)

Tool

Slotted screwdriver, 1.0 x 5.5 mm

Tightening torque

1.2 ... 1.5 Nm (10.6 lbf in)

For ring cable lugs without insulation

The power plug is included in the scope of supply.

5.6.3

Protective conductor connection

①

②

Protective conductor connection at the power plug
Protective conductor connection at the housing

You can connect the protective conductor either at the power plug or at the housing.

The protective conductor connection at the housing is located next to the strain relief plate.

Protective conductor connection at the
housing

Technical specifications

Screw

Ring/pipe-type cable lug

Tool

Torx screwdriver T20

Tightening torque

3 Nm (26.6 lbf in)

For further information about protective connections, please refer to Chapter "Protective
connection and equipotential bonding (Page 138)".

Smart Line Modules
5.6 Interface description

Booksize power units

Equipment Manual, 01/2022, 6SL3097-6AC30-0BP0

Содержание SINAMICS S220





























































































































































Результаты поиска

Содержание SINAMICS S220

Отзывы:

Siemens SINAMICS S220, Руководство по эксплуатации оборудования, Страница: 62 / 156

Результаты поиска

Содержание SINAMICS S220

Отзывы: