Siemens SINAMICS S220 Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 156

Siemens SINAMICS S220 Скачать руководство пользователя страница 57

5.3

Safety instructions for Smart Line Modules Booksize

WARNING

Electric shock when the protective flap of the DC link is open

Contact with live parts can result in death or serious injury.
• Only operate the components with closed protective flap.

WARNING

High leakage currents when the protective conductor in the line supply cable is
interrupted

The drive components conduct a high leakage current via the protective conductor. Touching
conductive parts when the protective conductor is interrupted can result in death or serious
injury.
• Carefully comply with the applicable regulations for dimensioning the protective conductor

(see Chapter "Protective connection and equipotential bonding").

WARNING

Electric shock due to improper DC link connection

Incorrect connections can cause overheating and so fire and smoke development. There is also
a risk of an electric shock. This can result in serious injury or death.
• When connecting to the DC link, only use the DC link adapter that has been approved by

Siemens.

WARNING

Electric shock due to missing DC link side covers

Live parts are exposed if the DC link side covers are not fitted. Contact with these live parts could
cause an electric shock.
• Mount the side covers on the first and last component in the drive lineup.
• Order any missing side covers (Article number: 6SL3162-5AA00-0AA0).

WARNING

Fire due to overheating resulting from power cables with inadequate cable cross-sections

Power cables with excessively low cross-sections can cause them to overheat. This can result in
severe injury or death due to fire and smoke.
• Only use power cables with sufficiently large cross-sections. Take into account the routing

type, ambient temperature and cable length.

Smart Line Modules

5.3 Safety instructions for Smart Line Modules Booksize

Booksize power units
Equipment Manual, 01/2022, 6SL3097-6AC30-0BP0

55

«
...
55
56
57
58
59
...
»

Содержание SINAMICS S220





























































































































































Отзывы:

Нет отзывов