Siemens SINAMICS S220 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 156

Siemens SINAMICS S220 Скачать руководство пользователя страница 41

4.2

Overcurrent protection using fuses and circuit breakers

You must use line fuses or circuit breakers for overcurrent protection. The following protective
elements can result in reductions.

Detailed specifications regarding protective devices and their respective short-circuit current
rating values can be found in the Product Information "Protective Devices for S220 Line Modules
Booksize (

https://support.industry.siemens.com/cs/ww/en/view/109804134

WARNING

Electric shock or fire due to overcurrent protective devices that trip too late or not at all

Overcurrent protective devices that trip too late or not all can cause electric shock or fire.
• In the case of a conductor-conductor or conductor-ground short-circuit, ensure that the

short-circuit current at the point where the converter is connected to the line supply
corresponds as a minimum to the requirements of the protective device used.

• You must additionally use a residual current device (RCD) if, for a conductor-ground short

circuit, the required short-circuit current is not reached. The required short-circuit current
can be too low, especially for TT line supply systems.

• The short-circuit current must not exceed the SCCR of the converter and the breaking

capacity of the protective device.

Line connection and line-side power components

4.2 Overcurrent protection using fuses and circuit breakers

Booksize power units
Equipment Manual, 01/2022, 6SL3097-6AC30-0BP0

39

«
...
39
40
41
42
43
...
»

Содержание SINAMICS S220





























































































































































Отзывы:

Нет отзывов