manualshive.com logo in svg

Siemens SINAMICS S220, Руководство по эксплуатации оборудования, Страница: 128 / 156

Поделиться
Скачать
Siemens SINAMICS S220 Скачать руководство пользователя страница 128

8.8.2

Options for the 24 V supply of the components

Line Modules, Motor Modules and DC link components are connected via the integrated 24 V 
busbars. The current-carrying capacity of these busbars is 20 A.

You can use the following components for the 24 V supply:

• Control Supply Module

• External 24 V power supply (e.g. SITOP)

• SITOP-PSU400M

Note
Using the SITOP PSU400M

More information on the SITOP PSU400M is provided in Chapter SITOP PSU400M (Page 102).

Using a Control Supply Module

When a Control Supply Module is used, the 24 V supply is directly established via the busbars. 
The electronic current limiting function integrated in the Control Supply Module protects the 
busbar system when a fault occurs. Additional loads can be connected via the 24 V terminal 
adapter.

Note

If you use cables with a cross-section of 2.5 mm

2

, no additional protection is required on the 

24 V side for the following cable types:
• Cables of the XLPE type
• Cables of the EPR type
• Cable with a similar properties and which is thermally stable up to 90 °C

2,5 mm

2

Motor

Module 

Motor

Module 

Line

Module

Control

Supply

Module

+

M

M

M

M

M

+

+

X124

+ 24 V

CU320-2

F1

Figure 8-2

Example of a 24 V supply via a Control Supply Module

Control cabinet design and EMC booksize
8.8 24 V DC supply voltage

Booksize power units

126

Equipment Manual, 01/2022, 6SL3097-6AC30-0BP0

Содержание SINAMICS S220





























































































































































Отзывы:

Нет отзывов