Siemens SINAMICS S220 Скачать руководство пользователя страница 122

Страница: 122 / 156

8.7

Electrical connection

Before commissioning, you must have completed the connection of the DC link busbars and 24
V busbars between all of the components.

Releasing the DC link protective flap and connecting the DC link busbars is identical for S220 and
S120 components. The procedure for S120 components is described in the next sections.

8.7.1

Connecting the DC link busbars and the 24 V busbars

Releasing the DC link protective flap

The protective flaps for the component DC links have an interlock mechanism.

Required tool:

• Flat bladed screwdriver (1 x 5.5)

To open the protective flap, use a screwdriver (1 x 5.5) to slightly turn the interlock screw in the
counter-clockwise direction.

'&3
'&1

[

Connecting DC link busbars

The connection of a Line Module to a Motor Module is shown in the following.

24 V busbars

DC link busbars

Line Module

Motor Module

DCP

DCN

Figure 8-1

Line Module and Motor Module as delivered

Always connect the lower DC link busbars first and then the upper DC link busbars.

Control cabinet design and EMC booksize
8.7 Electrical connection

Booksize power units

120

Equipment Manual, 01/2022, 6SL3097-6AC30-0BP0

Содержание SINAMICS S220





























































































































































Результаты поиска

Содержание SINAMICS S220

Отзывы:

Siemens SINAMICS S220, Руководство по эксплуатации оборудования, Страница: 122 / 156

Результаты поиска

Содержание SINAMICS S220

Отзывы: