Siemens SINAMICS G120 PM240P-2 страница 58 Скачать руководство пользователя

Страница: 58 / 106

Technical data

6.3 Overload capability of the converter

Power Module PM240P-2

Hardware Installation Manual, 06/2020, A5E37800827C AD

6.3

Overload capability of the converter

Overload capability is the property of the converter to temporarily supply a current that is

higher than the rated current to accelerate a load. Two typical load cycles are defined to

clearly demonstrate the overload capability: "Low Overload" and "High Overload"

Definitions

Base load
Constant load between the accelerating phases of the drive

Low Overload

High Overload

•

LO base load input current

Permissible input current for a "Low

Overload" load cycle

•

LO base load output current

Permissible output current for a "Low

Overload" load cycle

•

LO base load power

Rated power based on the LO base load

output current

•

HO base load input current

Permissible input current for a "High

Overload" load cycle

•

HO base load output current

Permissible output current for a "High

Overload" load cycle

•

HO base load power

Rated power based on the HO base

load output current

If not specified otherwise, the power and current data in the technical data always refer to a

load cycle according to Low Overload.
We recommend using the "SIZER" engineering software to select the converter.
You can find additional information about SIZER on the Internet:

Download Sizer

(

http://support.automation.siemens.com/WW/view/en/10804987/130000

)

Содержание SINAMICS G120 PM240P-2











































































































Результаты поиска

Содержание SINAMICS G120 PM240P-2

Отзывы:

Похожие инструкции для SINAMICS G120 PM240P-2

Бренды по названию

Популярные бренды

Siemens SINAMICS G120 PM240P-2, Руководство по установке

Результаты поиска

Содержание SINAMICS G120 PM240P-2

Отзывы:

Похожие инструкции для SINAMICS G120 PM240P-2

Бренды по названию

Популярные бренды