Siemens SINAMICS G120 PM240P-2 страница 32 Скачать руководство пользователя

Страница: 32 / 106

Installing

3.4 Mounting the Power Modules

Power Module PM240P-2

Hardware Installation Manual, 06/2020, A5E37800827C AD

3.4.4

Mounting the shield plate and EMC connecting bracket

Use the shield plate provided for strain relief of the line and motor cable – as well as the

shield support for the motor cable.
If you are using the converter without filter, then you do not require the EMC connecting

bracket. In this case, attach the shield plate to the converter without the EMC connecting

bracket
If you are using a converter with integrated line filter, then mount the shield plate and EMC

connecting bracket as described below.

Note
Brake relay
If you are using a brake relay to control a motor brake, then mount the brake relay at the rear

of the lower shield plate before you attach the shield module to the converter.

Motor holding brake (Page 81)

Procedure - FSD and FSE

Proceed as follows to mount the EMC connecting bracket and the shield plate:
1.

Attach the EMC connecting bracket to the shield plate

①

Then slide the shield module into the converter, so that it is held in the converter

②

the clamping spring. The shield module is located correctly if it can be easily withdrawn

out of the converter without any resistance.

After you have ensured that it is correctly located, fix the shield module using the four

screws

③

You have correctly mounted the EMC connecting bracket and the shield plate.

Содержание SINAMICS G120 PM240P-2











































































































Результаты поиска

Содержание SINAMICS G120 PM240P-2

Отзывы:

Похожие инструкции для SINAMICS G120 PM240P-2

Бренды по названию

Популярные бренды

Siemens SINAMICS G120 PM240P-2, Руководство по установке

Результаты поиска

Содержание SINAMICS G120 PM240P-2

Отзывы:

Похожие инструкции для SINAMICS G120 PM240P-2

Бренды по названию

Популярные бренды