Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 62

Страница: 62 / 346

Commissioning

4.3 Commissioning with factory settings

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

4.3

Commissioning with factory settings

Prerequisites for using the factory settings

In simple applications, commissioning can be carried out just using the factory settings.

Check which factory settings can be used and which functions need to be changed. During

this check you will probably find that the factory settings only require slight adjustment:
1.

The inverter and motor must match one another; compare the data on the motor rating

plate with the technical data of the Power Module.
–

The rated inverter current must, as a minimum, be the same as the motor.

–

The motor power should match that of the inverter; motors can be operated in the

power range from 25 % … 100 % of the inverter power rating.

If you are controlling the drive using the digital and analog inputs, the inverter must be

connected as shown in the wiring example. (see Wiring examples for the factory settings

(Page 61) )

If you connect the drive to a fieldbus, you must set the bus address using the DIP

switches on the front of the Control Unit.

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы:

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 62 / 346

Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы: