Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 338

Страница: 338 / 346

Appendix

A.2 Additional information on the inverter

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN

336

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

A.2

Additional information on the inverter

A.2.1

Manuals for your inverter

Table A- 6

Manuals for your converter

Depth of
the
information

Manual

Contents

Languages

Download or order number

Getting Started

Control Units CU230P-2;

CU240B-2; CU240E-2

Installing the converter and

commissioning.

Getting Started

SINAMICS G120 Power

Module

Installing the Power Module

Operating instructions

(this manual)

English,

German,

Italian,

French,

Spanish

+++

List Manual

Control Units CU230P-2

Graphic function block

diagrams.
List of all parameters, alarms

and faults.

+++

Hardware Installation

Manual

•

PM230 Power Module

•

PM240 Power Module

•

PM250 Power Module

•

PM260 Power Module

Installing power modules,

reactors and filters.
Maintaining power modules.

+++

Operating and installation

instructions

For converter accessories,

e.g. operator panel, reactors

or filter.

German,

English

Download manuals

(

Order numbers:

SD Manual Collection (DVD)

•

6SL3298-0CA00-0MG0
Supplied once.

•

6SL3298-0CA10-0MG0
Update Service for 1
year; supplied 4 times per
year.

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы:

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 338 / 346

Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы: