Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 27

Страница: 27 / 346

Description

2.3 Power Module

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

2.3

Power Module

Power Modules are available in various degrees of protection with a different topology in the

power range from between 0.37 kW up to 250 kW. The Power Modules are sub-divided into

various frame sizes (FS).

Power Modules with degree of protection IP20: PM240, PM250, PM260

Frame size

FSA

FSB

FSC

FSD

FSE

FSF

FSGX

PM240, 3AC 400V - power units with integrated braking chopper

Power range (LO) in kW

0.37 … 1.5

2.2 … 4

7.5 … 15 18.5 … 30

37 … 45

55 … 132 160 … 250

line filter, Class A

○

●

◑

PM250, 3AC 400V - power units capable of energy recovery
Power range (LO) in kW

---

7.5 … 15

18.5 … 30 37 … 45

55 … 90

---

line filter, Class A

---

●

---

PM260, 3AC 690V - power units capable of energy recovery
Power range (LO) in kW

---

11 … 18.5

---

30 … 55

---

line filter, Class A

---

○/●

---

○/●

---

Sine-wave filter

---

●

---

●

---

○ = without; ● = integrated; ◑ = from 110 kW for external mounting
1) The Power Module PM240 FSGX is supplied without braking chopper, but is prepared for installation of an optional

braking chopper

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы:

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 27 / 346

Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы: