manualshive.com logo in svg

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 263 / 346

Поделиться
Скачать
Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 263

 

Functions 

 

7.9 Application-specific functions 

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN 
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD 

261

 

7.9.12

 

Cascade control 

The cascade control function is used in applications that require between one and four 

motors to be run at the same time depending on load, so that e.g. highly variable pressure 

ratios or flow volumes can be corrected.  
Cascade control consists of the speed-controlled main drive and up to three other drives that 

are switched-on or switched-off via contactors or motor starters, either in a fixed 

arrangement or dependent on the operating hours.  
The PID deviation serves as the input signal for activating the other motors. The contactors 

or motor starters are switched by the inverter's digital outputs. 

 

 

Note 
Technology controller as main setpoint 
For cascade control, the main setpoint must be entered via the technology controller (p2251 

= 0, p2200 = 1).  

 

Operating principle 

●

 

Switching-in external motors 
If the main drive is run at maximum speed and the deviation on the technology controller 

input continues to increase, the control also switches the external motors on the line. At 

the same time, the main drive is ramped down to the switch-on/switch-off speed (p2378) 

to keep the total output power as constant as possible. The technology controller is 

deactivated while ramping down to the switch-on/switch-off speed. 

●

 

Shutting down external motors 
If the main drive is running at minimum speed and the deviation on the technology 

controller input continues to decrease, the control switches external motors M1 to M3 off 

the line. The main drive is simultaneously ramped-up to the switch-on/switch-off speed to 

keep the total output power as constant as possible. 

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Отзывы:

Нет отзывов