Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 251

Страница: 251 / 346

Functions

7.9 Application-specific functions

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

249

7.9.8

Time switch (DTC)

The "time switch" (DTC) function, along with the real time clock in the inverter, offers the

option of controlling when signals are switched on and off.

Examples:
●

Day/night switching of a temperature control

●

Switching a process control from weekday to weekend.

Principle of operation of the time switch (DTC)

The inverter has three independent parameterizable time switches. Using BICO technology,

the time switch output can be interconnected with every binector of your inverter, e.g. a

digital output or a technology controller's enable signal.

'7&RXWSXW
U

0RQGD\

7XHVGD\

:HGQHVGD\

7KXUVGD\

'HDFWLYDWHG

$FWLYDWHG

'HDFWLYDWHG

'7&ZHHNGD\
DFWLYDWLRQ

'7&VZLWFKLQJWLPHV

2))

57&
SS
U

S>@ S>@
S>@ S>@

S>@

Figure 7-20 Time behavior of the time switch using example DTC1

Parameterizing the time switch
●

Enable parameterization of the DTC: p8409 = 0.

As long as DTC parameterization is enabled, the inverter keeps the output of all three

DTC (r84x3, x = 1, 2, 3) on LOW.

●

Parameterize the activation of the weekdays; the switching on and off times.

●

Enable the setting: p8409 = 1.

The inverter enables the DTC outputs once more.

Additional information is provided in the parameter list of the List Manual.

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы:

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 251 / 346

Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы: