Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 246

Страница: 246 / 346

Functions

7.9 Application-specific functions

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN

244

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

7.9.5

Load torque monitoring (system protection)

In many applications, it is advisable to monitor the motor torque:
●

Applications where the load speed can be indirectly monitored by means of the load

torque. For example, in fans and conveyor belts too low a torque indicates that the drive

belt is torn.

●

Applications that are to be protected against overload or locking (e.g. extruders or

mixers).

●

Applications in which no-load operation of the motor represents an impermissible

situation (e.g. pumps).

Load torque monitoring functions

The converter monitors the torque of the motor in different ways:
1.

No-load monitoring:

The converter generates a message if the motor torque is too low.

Blocking protection:

The converter generates a message if the motor speed cannot match the speed setpoint

despite maximum torque.

Stall protection:

The converter generates a message if the converter control has lost the orientation of the

motor.

Speed-dependent torque monitoring

The converter measures the actual torque and compares it with a parameterized

speed/torque characteristic.

6SHHG>USP@

3VSHHGWKUHVKROG

3VSHHG

WKUHVKROG

3PD[LPXPVSHHG

3WRUTXHWKUHVKROG

ERWWRP

3WRUTXHWKUHVKROG

WRS

3WRUTXHWKUHVKROG

ERWWRP

3WRUTXHWKUHVKROG

WRS

3WRUTXHWKUHVKROG

ERWWRP

3WRUTXHWKUHVKROG

WRS

7RUTXH>1P@

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы:

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 246 / 346

Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы: