manualshive.com logo in svg

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 241 / 346

Поделиться
Скачать
Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 241

 

Functions 

 

7.9 Application-specific functions 

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN 
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD 

239

 

7.9.3.2

 

Automatic switch-on 

The automatic restart includes two different functions: 
1.

 

The inverter automatically acknowledges faults. 

2.

 

After a fault occurs or after a power failure, the inverter automatically switches-on the 

motor again.  

This automatic restart function is primarily used in applications where the motor is controlled 

locally via the inverter's inputs. In applications with a connection to a fieldbus, the central 

control should evaluate the feedback signals of the drives, specifically acknowledge faults or 

switch-on the motor. 
The inverter interprets the following events as power failure:  
●

 

The inverter signals fault F30003 (DC link undervoltage), as the line supply voltage of the 

inverter has briefly failed. 

●

 

The inverter power supply has failed for a long enough time so that the inverter has been 

switched-off. 

WARNING 

 

 

When the "automatic restart" function is active (p1210 > 1), the motor automatically 

starts after a power failure. This is especially critical after longer power failures.  
Reduce the risk of accidents in your machine or system to an acceptable level by 

applying suitable measures, e.g. protective doors or covers. 

Commissioning the automatic restart 

●

 

If it is possible that the motor is still rotating for a longer period of time after a power 

failure or after a fault, then in addition, you must activate the "flying restart" function, see 

Flying restart – switching on while the motor is running (Page 237). 

●

 

Using p1210, select the automatic restart mode that best suits your application. 

$XWRPDWLFUHVWDUW$5PRGH

$IWHUSRZHU

IDLOXUH

$IWHUSRZHU

IDLOXUHDQG

IDXOWV

$IWHUSRZHU

IDLOXUHDQG

IDXOWV

$IWHUSRZHU

IDLOXUH

1R$5

$FNQRZOHGJHIDXOWV

DXWRPDWLFDOO\

'RQRWVZLWFKRIIPRWRU

DXWRPDWLFDOO\

$FNQRZOHGJHIDXOWV

DXWRPDWLFDOO\

6ZLWFKRQPRWRUDXWRPDWL

FDOO\

$FNQRZOHGJHIDXOWV

DXWRPDWLFDOO\LI212))

FRPPDQG

6ZLWFKRQPRWRUDXWRPDWL

FDOO\

'RQRWDFNQRZOHGJHIDXOWV

DXWRPDWLFDOO\

6ZLWFKRQPRWRUDXWRPDWL

FDOO\

S 

S 

S 

S 

S 

S 

S 

 

Figure 7-16  Selecting the automatic restart mode 

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Отзывы:

Нет отзывов