Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 229

Страница: 229 / 346

Functions

7.9 Application-specific functions

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

227

Braking with regenerative feedback into the line

supply
The inverter feeds the regenerative power back into

the line supply.

•

Advantages: Constant braking torque; the

regenerative power is not converted into heat, but

is regenerated into the line supply; can be used in

all applications; continuous regenerative

operation is possible - e.g. when lowering a crane

load

•

Disadvantage: Does not function when power

fails

,QYHUWHU

/LQH

%UDNH

SRZHU

/RDG

0RWRU

,QYHUWHU

Braking with regenerative feedback into

the line supply

Braking method depending on the application

Table 7- 33 What Power Module is suitable for what application?

Application examples

Electrical braking methods

Power Modules that can be
used

Pumps, fans, mixers,

compressors, extruders

Not required

PM230, PM240, PM250,

PM260

Grinding machines, conveyor

belts

DC braking, compound braking

PM240

Dynamic braking

PM240

Centrifuges, vertical conveyors,

hoisting gear, cranes, winders

Braking with regenerative feedback

into the line supply

PM250, PM260

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы:

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 229 / 346

Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы: