manualshive.com logo in svg

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 227 / 346

Поделиться
Скачать
Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 227

 

Functions 

 

7.9 Application-specific functions 

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN 
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD 

225

 

7.9.2

 

Braking functions of the converter 

7.9.2.1

 

Comparison of electrical braking methods 

Regenerative power  

If an induction motor electrically brakes the connected load and the mechanical power 

exceeds the electrical losses, then it operates as a generator. The motor converts 

mechanical power into electrical power. Examples of applications, in which regenerative 

operation briefly occurs, include: 
●

 

Grinding disk drives 

●

 

Fans 

For certain drive applications, the motor can operate in the regenerative mode for longer 

periods of time, e.g.: 
●

 

Centrifuges 

●

 

Hoisting gear and cranes  

●

 

Conveyor belts with downward movement of load (vertical or inclined conveyors)  

Depending on the Power Modules used, SINAMICS G inverters offer the following options to 

either convert the regenerative power of the motor into heat or to feed this power back into 

the line supply: 
●

 

DC braking (Page 228) 

for Power Modules PM230, PM240, PM250 and PM260 

●

 

Compound braking (Page 232) 

for Power Module PM240 

●

 

Dynamic braking (Page 234) 

for Power Module PM240 

●

 

Braking with regenerative feedback to the line (Page 236) 

for Power Modules PM250 and 260 

A comparison with the main features of the individual braking functions is listed in the 

following paragraphs.  

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Отзывы:

Нет отзывов