manualshive.com logo in svg

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 225 / 346

Поделиться
Скачать
Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 225

 

Functions 

 

7.9 Application-specific functions 

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN 
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD 

223

 

7.9.1.4

 

Changing of the units with STARTER 

The converter must be in the offline mode in order to change over the units. 
STARTER shows whether you change settings online in the converter or change offline in 

the PC (

 / 

). 

 

You switch over the mode using the adjacent 

buttons in the menu bar.  

(VWDEOLVKWKHRQOLQH

FRQQHFWLRQ

*RRIIOLQH

GLVFRQQHFW

 

Procedure 

●

 

Go to the "Units" tab in the configuration screen form to change over the units. 

 

③

 

  Changing over the unit system 

④

 

  Selecting process variables of the technology controller 

⑤

 

  Select process variables of the additional technology controller 0 

⑥

 

  Select process variables of the additional technology controller 2 

⑦

 

  Select process variables of the additional technology controller 1 

⑧

 

  adapting to the line supply 

Figure 7-11  Unit changeover 

●

 

Save your settings 

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Отзывы:

Нет отзывов