Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 216

Страница: 216 / 346

Functions

7.7 Protection functions

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN

214

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

Parameters to set the motor temperature monitoring with sensor

Table 7- 28 Parameters for detecting the motor temperature via a temperature sensor

Parameter

Description

P0335

Specify the motor cooling

0: Self-ventilated - with fan on the motor shaft (IC410* or IC411*) - (factory setting)

1: Forced ventilation - with a separately driven fan (IC416*)

2: Self-ventilated and inner cooling* (open-circuit air cooled)

3: Forced ventilated and inner cooling* (open-circuit air cooled)

Terminal no.
14

PTC+

KTY anode

ThermoClick

P0601

Motor temperature sensor type

0: No sensor (factory setting)

1: PTC thermistor (→ P0604)

2: KTY84 (→ P0604)

4: ThermoClick sensor

PTC-

KTY cathode

ThermoClick

P0604

Motor temperature alarm threshold (factory setting 130 °C)

The alarm threshold is the value at which the inverter is either shut down or I

max

reduced (P0610)

P0605

Motor temperature fault threshold (Factory setting: 145 °C)

P0610

Motor overtemperature response

Determines the response when the motor temperature reaches the alarm threshold.
0: No motor response, only an alarm

1: Alarm and reduction of I

max

(factory setting)

reduces the output speed

2: Fault message and shutdown (F07011)

P0640

Current limit (input in A)

*According to EN 60034-6

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы:

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 216 / 346

Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы: