manualshive.com logo in svg

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 204 / 346

Поделиться
Скачать
Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 204

Functions 

 

7.5 Setpoint calculation 

 

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN 

202

 

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD 

7.5

 

Setpoint calculation 

The setpoint processing modifies the speed setpoint, e.g. it limits the setpoint to a maximum 

and minimum value and using the ramp-function generator prevents the motor from 

executing speed steps.  

6SHHGVHWSRLQWIURP
VHWSRLQWVRXUFH

3RVLWLYH

/LPLWDWLRQ

QHJDWLYH

/LPLWDWLRQ

5DPSIXQFWLRQJHQHUDWRU

5DPSXS

WLPH

5DPS

GRZQWLPH

6SHHGVHWSRLQWIRU
PRWRUFRQWURO

 

Figure 7-10  Setpoint processing in the inverter 

7.5.1

 

Minimum speed and maximum speed 

The speed setpoint is limited by both the minimum and maximum speed.  
When the motor is switched on, it accelerates to the minimum speed regardless of the speed 

setpoint. The set parameter value applies to both directions of rotation. Beyond its limiting 

function, the minimum speed serves as a reference value for a series of monitoring 

functions. 
The speed setpoint is limited to the maximum speed in both directions of rotation. The 

inverter generates a message (fault or alarm) when the maximum speed is exceeded. 
The maximum speed also acts as an important reference value for various functions (e.g. the 

ramp-function generator). 

Table 7- 24  Parameters for minimum and maximum speed 

Parameter  

Description  

P1080 

Minimum speed 

P1082 

Maximum speed 

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Отзывы:

Нет отзывов