manualshive.com logo in svg

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 202 / 346

Поделиться
Скачать
Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 202

Functions 

 

7.4 Setpoint sources 

 

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN 

200

 

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD 

Example: Selecting two fixed speed setpoints using digital input 2 and digital input 3 

The motor is to run at two different speeds: 
●

 

The motor is switched on with digital input 0 

●

 

When digital input 2 is selected, the motor is to run at a speed of 300 rpm. 

●

 

When digital input 3 is selected, the motor is to accelerate to a speed of 2000 rpm. 

●

 

When digital input 1 is selected, the motor should go into reverse 

Table 7- 21  Parameter settings for the example 

Parameter 

Description 

p0015 = 12 

Macro drive unit: Configure inverter with terminal strip as the command 

and setpoint source. 

•

 

The motor is switched on and off via digital input 0. 

•

 

The setpoint source is analog input 0. 

p1001 = 300.000 

Defines the fixed setpoint 1 in [rpm] 

p1002 = 2000.000 

Defines the fixed setpoint 2 in [rpm] 

p1016 = 1 

Direct selection of fixed setpoints 

p1020 = 722.2 

Interconnection of fixed setpoint 2 with DI 2.  

r0722.2 = parameter that displays the status of digital input 2. 

p1021 = 722.3 

Interconnection of fixed setpoint 3 with status of DI 3.  

r0722.3 = parameter that displays the status of digital input 3. 

p1070 = 1024 

Interconnect main setpoint with fixed speed setpoint 

7.4.4

 

Running the motor in jog mode (JOG function) 

Using the "jog" function (JOG function), you can switch the motor on and off using a control 

command or the operator panel. The speed to which the motor accelerates for "Jog" can be 

set. 
The motor must be switched-off before you issue the "jog" control command. "Jog" has no 

effect when the motor is switched on. 
The "Jog" function is typically used to manually switch-on a motor after switching over from 

automatic to manual operation.  

Setting jogging 

The "Jog" function has two different speed setpoints, e.g. for motor counter-clockwise 

rotation and clockwise rotation. 
With an operator panel, you can always select the "Jog" function. If you wish to use 

additional digital inputs as control commands, you must interconnect the particular signal 

source with a digital input. 

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Отзывы:

Нет отзывов