Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 198

Страница: 198 / 346

Functions

7.4 Setpoint sources

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN

196

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

7.4.2

Motorized potentiometer as setpoint source

The 'motorized potentiometer' (MOP) function simulates an electromechanical potentiometer

for entering setpoints. You can continuously adjust the motorized potentiometer (MOP) using

the control signals "raise" and "lower". The control signals are received via the digital inputs

of the inverter or from the operator panel that has been inserted.

Typical applications

●

Entering the speed setpoint during the commissioning phase.

●

Manual operation of the motor should the higher-level control fail.

●

Entering the speed setpoint after changeover from automatic operation to manual

operation.

●

Applications with largely constant setpoint and without higher-level control.

Principle of operation

023GRZQ

023XS

2))GRZQUDPS

023U

212))

PD[

Figure 7-9

Function chart of motorized potentiometer

Motorized potentiometer parameters

Table 7- 16 Basic setup of motorized potentiometer

Parameter

Description

p1047

MOP ramp-up time (factory setting 10 s)

p1048

MOP ramp-down time (factory setting 10 s)

p1040

Start value of MOP (factory setting 0 rpm)

Determines the start value [rpm] that becomes effective when the motor is switched

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы:

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 198 / 346

Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы: