Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 180

Страница: 180 / 346

Configuring the fieldbus

6.3 Communication over CANopen

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN

178

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

6.3.4.2

Objects in drive profile DSP402

The following table lists the object directory with the index of the individual objects for the

drives.

Table 6- 53 Objects in drive profile DSP402

OD index
(hex)

Sub-
index
(hex)

Name of the object

SINAMICS
parameters

Transmissio
n

Data type

Default
setting

Can be
read/
written
to

Predefinitions
67FF

Single device type

SDO

Unsigned32

Common entries in the object dictionary
6007

Abort connection option code p8641

SDO

Integer16

R/W

6502

Supported drive modes

SDO

Integer32

6504

Drive manufacturer

SDO

String

SIEMENS

Device control
6040

Control word

r8795

PDO/SDO Unsigned16

–

R/W

6041

Status word

r8784

PDO/SDO Unsigned16

–

6060

Modes of operation

p1300

SDO

Integer8

–

6061

Modes of operation display

p1300

SDO

Integer8

–

Profile torque mode
6071

Target torque
Set torque

p1513[0]

SDO/PDO Integer16

–

R/W

6072

Max. torque

p1520/p1521 SDO

Real32

R/W

6074

Torque demand value
Actual torque

r0080

SDO/PDO Integer16

–

Velocity mode
6042

vl target velocity

r0060

SDO/PDO Integer16

R/W

6044

vl control effort

r0063

SDO/PDO Integer16

1) SDO access is only possible after mapping the objects and the BICO interconnection to

display parameters.
2) Object cannot be written to as a CANopen device profile is not supported, only

manufacturer-specific operating data

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы:

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 180 / 346

Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы: