Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 135

Страница: 135 / 346

Configuring the fieldbus

6.2 Communication via RS485

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

133

6.2.3

Communication over Modbus RTU

Overview of communication using Modbus

The Modbus protocol is a communication protocol with linear topology based on a

master/slave architecture.
Modbus offers three transmission modes:
●

Modbus ASCII

Data is transferred in ASCII code. The data can therefore be read directly by humans,

however, the data throughput is lower in comparison to RTU.

●

Modbus RTU

Modbus RTU (RTU: Remote Terminal Unit): Data is transferred in binary format and the

data throughput is greater than in ASCII code.

●

Modbus TCP

This type of data transmission is very similar to RTU, except that TCP/IP packages are

used to send the data. TCP port 502 is reserved for Modbus TCP. Modbus TCP is

currently undergoing definition as a standard (IEC PAS 62030 (pre-standard)).

The Control Unit supports Modbus RTU as a slave with even parity.

ELWVRIGDWD

%LW

VWRS

%LW

3HYHQ

%LW

6WDUW

Communication settings

●

Communication using Modbus RTU takes place over the RS485 interface with a

maximum of 247 slaves.

●

The maximum cable length is 1200 m (3281 ft).

●

Two 100 kΩ resistors are provided to polarize the receive and send cables.

CAUTION

It is not permitted to change over the units!
The "Unit changeover (Page 219)" function is not permissible with this bus system!

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы:

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 135 / 346

Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы: