Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 120

Страница: 120 / 346

Configuring the fieldbus

6.2 Communication via RS485

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN

118

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

6.2

Communication via RS485

6.2.1

Integrating inverters into a bus system via the RS485 interface

Connecting to a network via RS485

Connect the inverter to your fieldbus via the RS485 interface. Position and assignment of the

RS485 interface can be found in section Interfaces, connectors, switches, control terminals,

LEDs on the CU (Page 46). This connector has short-circuit proof, isolated pins.

%XVWHUPLQDWLQJ

UHVLVWRU

6KLHOG

/DVW56VODYH

,QYHUWHU

,QYHUWHUQ

56
0DVWHU

566ODYH

2))

Figure 6-4

Communication network via RS485

You must switch-in the bus terminating resistor for the first and last participants. The position

of the bus terminating resistor can be found in section Interfaces, connectors, switches,

control terminals, LEDs on the CU (Page 46).
You can disconnect one or more slaves from the bus (by unplugging the bus connector)

without interrupting the communication for the other stations, but not the first or last.

NOTICE

When the bus is operating, the first and last bus station must be continuously connected to

the supply.

Note
Communication with the controller, even when the supply voltage on the Power Module is

switched off
You will have to supply the Control Unit with 24 V DC on terminals 31 and 32 if you require

communication to take place with the controller when the line voltage is switched off.

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы:

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 120 / 346

Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы: