Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 112

Страница: 112 / 346

Configuring the fieldbus

6.1 Communication via PROFIBUS

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN

110

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

Parameter index (IND)

3.(

,1'

3:(

ZRUG

DQG

ZRUG

3DJHLQGH[

6XELQGH[,1'

3DUDPHWHUFKDQQHO

Figure 6-3

Structure of the parameter index (IND)

●

For indexed parameters, select the index of the parameter by transferring the appropriate

value between 0 and 254 to the subindex within a job.

●

The page index is used to switch over the parameter numbers. Use this byte to add an

offset to the parameter number that is transferred in the 1st word of the parameter

channel (PKE).

Page index: Offset of parameter number

The parameter numbers are assigned to several parameter ranges. The following table

shows which value you must transfer to the page index to achieve a particular parameter

number.

Table 6- 13 Page index setting dependent on parameter range

Page index

Parameter range

Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

Hex value

0000 … 1999

0x00

2000 … 3999

0x80

6000 … 7999

0x90

8000 … 9999

0x20

10000 … 11999

0xA0

20000 … 21999

0x50

30000 … 31999

0xF0

Parameter value (PWE)

The parameter value (PWE) is transferred as a double word (32 bits). Only one parameter

value may be transferred per telegram.
A 32 bit parameter value includes PWE1 (H word, 3rd word) and PWE2 (L word, 4th word).
A 16 bit parameter value is transferred in PWE2 (L word, 4th word). In this case, PWE1 (H

word, 3rd word) must be set to 0.

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы:

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 112 / 346

Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы: