Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 109

Страница: 109 / 346

Configuring the fieldbus

6.1 Communication via PROFIBUS

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

107

6.1.4.3

Data structure of the parameter channel

Parameter channel

You can write and read parameter values via the parameter channel, e.g. in order to monitor

process data. The parameter channel always comprises four words.

3.(

,1'

3:(

ZRUG

DQG

ZRUG

$EEUHYLDWLRQV

3DUDPHWHUFKDQQHO

3.(3DUDPHWHULGHQWLILHU
,1',QGH[
3:(3DUDPHWHUYDOXH

Figure 6-1

Structure of the parameter channel

Parameter identifier (PKE), 1st word

The parameter identifier (PKE) contains 16 bits.

3.(

,1'

3:(

318

ZRUG

3DUDPHWHUFKDQQHO

ZRUG

DQG

ZRUG

Figure 6-2

PKE - 1st word in parameter channel

●

Bits 12 to 15 (AK) contain the request or response identifier.

●

Bit 11 (SPM) is reserved and is always 0.

●

Bits 0 to 10 (PNU) contain parameter numbers 1 … 1999. For parameter numbers ≥ 2000

an offset must be added that is defined in the 2nd word of the parameter channel (IND).

The meaning of the request identifier for request telegrams (control → inverter) is explained

in the following table.

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы:

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 109 / 346

Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы: