Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 104

Страница: 104 / 346

Configuring the fieldbus

6.1 Communication via PROFIBUS

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN

102

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

Table 6- 5

Telegram status in the inverter

Control ⇒ inverter

Inverter ⇒ control

Process data
item

Status of the received
word

Bits 0…15 in the
received word

Defining the word to be
sent

Status of the sent word

PZD01

r2050[0]

r2090.0 … r2090.15

p2051[0]

r2053[0]

PZD02

r2050[1]

r2091.0 … r2091.15

p2051[1]

r2053[1]

PZD03

r2050[2]

r2092.0 … r2092.15

p2051[2]

r2053[2]

PZD04

r2050[3]

r2093.0 … r2093.15

p2051[3]

r2053[3]

PZD05

r2050[4]

p2051[4]

r2053[4]

PZD06

r2050[5]

p2051[5]

r2053[5]

PZD07

r2050[6]

p2051[6]

r2053[6]

PZD08

r2050[7]

p2051[7]

r2053[7]

Select telegram

Select the communication telegram using parameters p0922 and p2079. The following

dependencies apply:
●

P0922 < 999:

For p0922 < 999, the inverter sets p2079 to the same value as p0922.

With this setting, the inverter defines the length and the content of the telegram. The

inverter does not permit any changes to the telegram.

●

p0922 = 999, p2079 < 999:

For p0922 = 999, select a telegram via p2079.

Also with this setting, the inverter defines the length and the content of the telegram. The

inverter does not permit any changes to the telegram content. However, you can extend

the telegram.

●

p0922 = p2079 = 999:

For p0922 = p2079 = 999, enter the length and the content of the telegram.

With this setting, you can define the telegram length via the central PROFIdrive

configuration in the master. You define the telegram contents via the signal

interconnections of the BICO technology. Using p2038, you can define the assignment of

the control word according to SINAMICS or VIK/NAMUR.

You will find more details on the interconnection of command and setpoint sources,

depending on the selected protocol, in the List Manual in function block diagrams 2420 to

2472.

6.1.4.1

Control and status word 1

The control and status words fulfill the specifications of PROFIdrive profile version 4.1 for

"speed control" mode.

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы:

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 104 / 346

Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы: