manualshive.com logo in svg

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 102 / 346

Поделиться
Скачать
Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 102

Configuring the fieldbus 

 

6.1 Communication via PROFIBUS 

 

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN 

100

 

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD 

6.1.3

 

Basic settings for communication 

Table 6- 1 

The most important parameters 

Parameter 

Description 

p0015  

Macro drive device 

Select the I/O configuration via PROFIBUS DP (e.g. p0015 = 7)  
PROFIdrive telegram selection (factory setting for converters with PROFIBUS 

interface: standard telegram 1, PZD-2/2) 
Set the send and receive telegram, see Cyclic communication (Page 101) 

p0922 

1:  

20:  

350:  

352 

353:  

354:  

999:  

Standard telegram 1, PZD-2/2 

Standard telegram 20, PZD-2/6 

SIEMENS telegram 350, PZD-4/4 

SIEMENS telegram 352, PZD-6/6 

SIEMENS telegram 353, PZD-2/2, PKW-4/4 

SIEMENS telegram 354, PZD-6/6, PKW-4/4 

Free telegram configuring with BICO 

Using parameter p0922, you automatically interconnect the corresponding signals of the 

converter to the telegram. 
This BICO interconnection can only be changed, if you set p0922 to 999. In this case, select 

your required telegram using p2079 and then adapt the BICO interconnection of the signals. 

Table 6- 2 

Advanced settings 

Parameter  Description 
p2079 

PROFIdrive PZD telegram selection extended 
Contrary to p0922, using p2079, a telegram can be set and subsequently extended. 

For p0922 < 999, the following applies: p2079 has the same value and is locked. All of 

the interconnections and extensions contained in the telegram are locked. 

For p0922 = 999, the following applies: p2079 can be freely set. If p2079 is also set to 

999, then all interconnections can be set. 

For p0922 = 999 and p2079 < 999, the following applies: The interconnections 

contained in the telegram are locked. However, the telegram can be extended. 

For further information, please refer to the Parameter Manual. 

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Отзывы:

Нет отзывов