manualshive.com logo in svg

Siemens sinamics dcp, Руководство пользователя

Продукт Siemens Sinamics DCP представляет собой высококачественный преобразователь частоты, который обеспечивает надежное управление электродвигателями. Вы можете бесплатно скачать его руководство по эксплуатации на manualshive.com для получения подробной информации о настройке и использовании этого устройства.

Поделиться
Скачать
background image

4 Faults and alarms
4.2 List of faults and alarms

SINAMICS DCP

394

 

List Manual (LH21), 05/2016

126: Write access only in the commissioning state, device ready (device: p0009 = 0).
127: Write access only in the commissioning state, device (device: p0009 not equal to 0).
129: Parameter may not be written in download.
130: Transfer of the master control is inhibited via binector input p0806.
131: Required BICO interconnection not possible because BICO output does not supply floating value
132: Free BICO interconnection inhibited via p0922.
133: Access method not defined.
200: Below the valid values.
201: Above the valid values.
202: Cannot be accessed from the Basic Operator Panel (BOP).
203: Cannot be read from the Basic Operator Panel (BOP).
204: Write access not permitted.

Remedy:

- enter the correct value in the specified parameter.
- identify the parameter that restricts the limits of the specified parameter.

F01043

Fatal error at project download

Drive object:

CU_DCP, TM150, TM15DI_DO, TM31

Cause:

A fatal error was detected when downloading a project using the commissioning software.
Fault value (r0949, interpret decimal):
1: Device status cannot be changed to Device Download (drive object ON?).
2: Incorrect drive object number.
3: A drive object that has already been deleted is deleted again.
4: Deleting of a drive object that has already been registered for generation.
5: Deleting a drive object that does not exist.
6: Generating an undeleted drive object that already existed.
7: Regenerating a drive object already registered for generation.
8: Maximum number of drive objects that can be generated exceeded.
9: Error while generating a device drive object.
10: Error while generating target topology parameters (p9902 and p9903).
11: Error while generating a drive object (global component).
12: Error while generating a drive object (drive component).
13: Unknown drive object type.
14: Drive status cannot be changed to "ready for operation" (r0947 and r0949).
15: Drive status cannot be changed to drive download.
16: Device status cannot be changed to "ready for operation".
17: It is not possible to download the topology. The component wiring should be checked, taking into account the 
various messages/signals.
18: A new download is only possible if the factory settings are restored for the drive unit.
19: The slot for the option module has been configured several times (e.g. CAN and COMM BOARD)
20: The configuration is inconsistent (e.g. CAN for Control Unit, however no CAN configured for drive objects A_INF, 
SERVO or VECTOR ).
21: Error when accepting the download parameters.
22: Software-internal download error.
Additional values: only for internal Siemens troubleshooting.

Remedy:

- use the current version of the commissioning software.
- modify the offline project and carry out a new download (e.g. compare the number of drive objects, motor, encoder, 
power unit in the offline project and at the drive).
- change the drive state (is a drive rotating or is there a message/signal?).
- carefully note any other messages/signals and remove their cause.
- boot from previously saved files (power-down/power-up or p0976).

F01044

CU: Descriptive data error

Drive object:

All objects

Cause:

An error was detected when loading the descriptive data saved in the non-volatile memory.

Remedy:

Replace the memory card or Control Unit.

Содержание sinamics dcp







































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для sinamics dcp

Cablematic HC44 User Manual preview
HC44
Бренд: Cablematic Страницы: 2
M-Audio MIDISPORT 1x1 Quick Start Manual preview
MIDISPORT 1x1
Бренд: M-Audio Страницы: 3
V-TAC 23070 Instruction Manual preview
23070
Бренд: V-TAC Страницы: 3
Sima STP-325 User Instructions preview
STP-325
Бренд: Sima Страницы: 2
Generac Power Systems 00919-0 Owner'S Manual preview
00919-0
Бренд: Generac Power Systems Страницы: 32
3onedata 3012SS User Manual preview
3012SS
Бренд: 3onedata Страницы: 7
Imerge MediaServer MS5000 User Manual preview
MediaServer MS5000
Бренд: Imerge Страницы: 68
GE GEP5.0-3-10 User Manual preview
GEP5.0-3-10
Бренд: GE Страницы: 55
KEB COMBIVERT F5 Series Instruction Manual preview
COMBIVERT F5 Series
Бренд: KEB Страницы: 116
W&T 81215 Manual preview
81215
Бренд: W&T Страницы: 12
BSPH SH-360 Operation Manual preview
SH-360
Бренд: BSPH Страницы: 36
Elation PRO HAZE DMX User Instructions preview
PRO HAZE DMX
Бренд: Elation Страницы: 8
Yuan HD2HD-4KS User Manual preview
HD2HD-4KS
Бренд: Yuan Страницы: 15
TDK-Lambda CC15-xxxx-Sxx-E Series Instruction Manual preview
CC15-xxxx-Sxx-E Series
Бренд: TDK-Lambda Страницы: 11
TR-Electronic PROFI BUS QDH Series User Manual preview
PROFI BUS QDH Series
Бренд: TR-Electronic Страницы: 135
Envivio 4Caster Broadcast 3500 Specifications preview
4Caster Broadcast 3500
Бренд: Envivio Страницы: 2
DCCconcepts Cobalt Alpha Series Manual preview
Cobalt Alpha Series
Бренд: DCCconcepts Страницы: 25
Shindaiwa DGK150D Owner'S And Operator'S Manual preview
DGK150D
Бренд: Shindaiwa Страницы: 58

Бренды по названию

Популярные бренды

Загрузить еще бренды