Siemens SIMOTION TM15 Скачать руководство пользователя страница 51

Страница: 51 / 99

TM15 / TM17 High Feature Operating Manual
Commissioning Manual, 05/2009

Error messages

Introduction

The error messages generated by the TM15 or TM17 High Feature modules are reported

cyclically to the SIMOTION Motion Control System via the module status word as well as the

diagnostic interrupt. The input address of the status word is identical to the start address (I-

address) of the module.

Status word structure

The error bit corresponds to bit 9 of the module status word.

ERR = 0:

No error

ERR = 1:

Error. The cause of error is indicated via

error bits MF, PS, and
FPGA.
For hotline purposes, drive parameter

P2122 contains a
detailed error code.
Error class if ERR = 1 is set
MF: Internal module error
PS: No I/O power supply
FPGA: Error in FPGA code

Bit

Function -

ERR SYNC -

FPGA PS

-: Reserved, must not be used

ERR

Error bit; indicates that the module is not

ready; more details are specified with bits

MF, PS and FPGA

SYNC

SYNC = 1 indicates that the TM1x module is

synchronized

Содержание SIMOTION TM15




































































































Результаты поиска

Содержание SIMOTION TM15

Отзывы:

Бренды по названию

Популярные бренды

Siemens SIMOTION TM15, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание SIMOTION TM15

Отзывы:

Бренды по названию

Популярные бренды