Siemens SIMOTION TM15 Скачать руководство пользователя страница 46

Страница: 46 / 99

Commissioning

3.2 Updating the firmware

TM15 / TM17 High Feature Operating Manual

Commissioning Manual, 05/2009

3.2

Updating the firmware

The module firmware can be updated using a CompactFlash Card, which is inserted in the

SIMOTION D or SINAMICS S120 Control Unit.

Procedure

Online connection for SCOUT
In the project tree, click "SINAMICS_Integrated".
Go online by clicking the "Connect to target system" symbol in the main toolbar at the top.
SCOUT is now connected to the SINAMICS device.

Figure 3-1

SCOUT project tree – Topology

Selection of Terminal Module
Double-click "Configuration" under "SINAMICS_Integrated". A window with two tabs

("PROFIBUS message frames" and "Version overview" will appear (similar to screen

below).
The "Version overview" tab contains all the components that are connected to the

SINAMICS Control Unit. The FW version currently installed on the component is

displayed in the FW version column. The first two digits stand for the version, i.e. 24....

stands for version V2.4.

Figure 3-2

Screen displaying components connected to the Control Unit

Содержание SIMOTION TM15




































































































Результаты поиска

Содержание SIMOTION TM15

Отзывы:

Бренды по названию

Популярные бренды

Siemens SIMOTION TM15, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание SIMOTION TM15

Отзывы:

Бренды по названию

Популярные бренды