Siemens SIMOTION TM15 Скачать руководство пользователя страница 45

Страница: 45 / 99

TM15 / TM17 High Feature Operating Manual
Commissioning Manual, 05/2009

Commissioning

3.1

Power-up

Once the terminal module is physically installed and connected electrically, power may be

applied to the unit.

DANGER

Ensure that installation and operation are in accordance with the instructions provided in

this Manual, and in accordance with the Safety Guidelines provided at the beginning of this

Manual. Failure to do so can result in serious injury or death.

Status LED (RDY) of module

The status of the module and the DRIVE-CLiQ interface are indicated by means of a

multicolored LED on the front panel of the TM. The individual colors are explained in the

following table. The error display is the same as that used on other SINAMICS components.

Table 3- 1

Module status

LEDs

Color

Status

Description

Off

Electronics power supply outside the

permissible tolerance range.

Green

Continuous light

The component is ready for operation and

cyclic DRIVE-CLiQ communication is taking

place.

Orange

Continuous light

DRIVE-CLiQ communication is being

established.

Red

Continuous light

This component has at least one fault.

Green/Red

Flashing 2 Hz

Firmware is being downloaded.

Green/Orange

Flashing 2 Hz

Component detection: no faults detected.

READY

Red/Orange

Flashing 2 Hz

Component detection: fault(s) detected.

Note
Interruption of module power supply: If the power supply to the module is interrupted, all

outputs will switch to 0 V until synchronous communication resumes.

Содержание SIMOTION TM15




































































































Результаты поиска

Содержание SIMOTION TM15

Отзывы:

Бренды по названию

Популярные бренды

Siemens SIMOTION TM15, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание SIMOTION TM15

Отзывы:

Бренды по названию

Популярные бренды