manualshive.com logo in svg

Siemens SIMOTION TM15, Руководство по вводу в эксплуатацию

Поделиться
Скачать
Siemens SIMOTION TM15 Скачать руководство пользователя страница 33

 

Configuration/programming 

 

2.3 Accessing inputs and outputs in a user task 

TM15 / TM17 High Feature Operating Manual 
Commissioning Manual, 05/2009 

33

 

Refer to the following figure for the offset in the example. 

 

Figure 2-8 

SCOUT – graphical configuration screen form for the TM17 (SIMOTION) 

Input DI 

The base "I-address" of the TM17 High Feature is "288". Now add the offset of 3.0. For DI 0, 

the resulting address is "291.0".  

Output DO 

The base "O-address" of the TM17 High Feature is "280". Now add the offset of 3.1. For DO 

1, the resulting address is "283.1".  
The procedures for generating symbolic variables and for using the process image or direct 

I/O access are described in the SIMOTION SCOUT Manual. 

 

 

Note 
You cannot use I/O variables to output to a digital output that is being used simultaneously 

by an Output Cam or Cam Track technology object. 
An error message will be output when the project is downloaded to the target system.  
Please also note that the Terminal Module must have ramped up before it is accessed via 

I/Os. You can also configure an error strategy for I/O (CPU stop, substitute value or last 

value). Note that byte-specific setting is the minimum possible setting. 
You cannot assign a substitute value for an output byte if individual bits have been allocated 

to an Output Cam or Cam Track technology object. 

 

See also 

Power Up and Synchronization with the User Program (Page 37) 

Содержание SIMOTION TM15




































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды