Siemens SIMOTION TM15 Скачать руководство пользователя страница 28

Страница: 28 / 99

Configuration/programming

2.2 Configuring and programming TM1x modules

TM15 / TM17 High Feature Operating Manual

Commissioning Manual, 05/2009

Table 2- 6

"Enable" and "Function" columns: Description of symbols

Symbol for enable signal selection
(Enable column)

Symbol for assigned input of enable

signal
(Function column)

Explanation

No enable input

No enable signal and therefore no

enable input selected.

Level-triggered enable signal. The

channel assigned for the enable signal

is displayed as an enable.

Edge-triggered enable signal
(setting option only available for

outputs of output cam).
The channel assigned for the enable

signal is displayed as a measuring

input. A Measuring Input technology

object must be configured in

SIMOTION for the input of the

measuring input. The Measuring Input

technology object can be used to

evaluate the positions of the enable

edges.

The enable signal polarity depends upon the selection you have made in the "Inverter"

column, as follows:

Table 2- 7

"Inverter" column: inverter options for enable signals

Enable signal selection
(Enable column)

Inverter options
(Inverter column)
Not inverted

Inverted

Level-triggered

Enable signal is high active

Enable signal is low active

Edge-triggered

Enable signal takes effect on a rising

edge

Enable signal takes effect on a falling

edge

Содержание SIMOTION TM15




































































































Результаты поиска

Содержание SIMOTION TM15

Отзывы:

Бренды по названию

Популярные бренды

Siemens SIMOTION TM15, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание SIMOTION TM15

Отзывы:

Бренды по названию

Популярные бренды