Siemens SIMOTION TM15 Скачать руководство пользователя страница 19

Страница: 19 / 99

TM15 / TM17 High Feature Operating Manual
Commissioning Manual, 05/2009

Configuration/programming

2.1

Requirement

To begin using the terminal modules, you need the following:

Hardware requirements

●

TM15 or TM17 High Feature

●

One of the following components:
–

SIMOTION D (TM is connected directly to SIMOTION D or CX32)

–

SIMOTION D (TM is connected to a Control Unit, which is connected via

PROFIBUS/PROFINET to SIMOTION D)

–

SIMOTION C (TM is connected to a Control Unit, which is connected via PROFIBUS

to SIMOTION C)

–

SIMOTION P (TM is connected to a Control Unit, which is connected via

PROFIBUS/PROFINET to SIMOTION P)

–

DIN rail in accordance with DIN EN 50 022 (35 x 15 / 7.5)

–

DRIVE-CLiQ cable

–

PROFIBUS or PROFINET cable

–

External 24 VDC power supply (note the requirements for the TM15 and TM17 High

Feature terminal modules)

Software requirements

This documentation describes
●

SIMOTION V4.1 incl. SP1 and

●

SINAMICS V2.5 incl. SP1

Previous SIMOTION and SINAMICS versions do not include all the functions described in

this Manual.

Содержание SIMOTION TM15




































































































Результаты поиска

Содержание SIMOTION TM15

Отзывы:

Бренды по названию

Популярные бренды

Siemens SIMOTION TM15, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание SIMOTION TM15

Отзывы:

Бренды по названию

Популярные бренды