Siemens SIMOTION TM15 Скачать руководство пользователя страница 13

Страница: 13 / 99

Description

1.2 Properties: TM15 / TM17 High Feature

TM15 / TM17 High Feature Operating Manual
Commissioning Manual, 05/2009

1.2

Properties: TM15 / TM17 High Feature

Figure 1-3

Terminal Module TM15 and Terminal Module TM17 High Feature

The properties of the Terminal Modules are presented below. This overview is intended to

help you select the appropriate module for your application.

Properties

The TM15 and TM17 High Feature Terminal Modules are terminal expansion modules

designed to be mounted on a DIN rail in accordance with DIN EN 50 022.
The Terminal Modules contain the following:
●

2 DRIVE CLiQ sockets

●

Connection for 24 VDC electronic power supply

●

The logical status of the I/O channel is indicated by the associated green status LED.

●

The status of the TM15/TM17 High Feature is indicated by a multi-colored RDY LED.

Each of the 24 DI/DO (TM15) or 16 DI/DO (TM17 High Feature) can be parameterized on a

channel-specific basis as a digital input (DI), digital output (DO), input of a measuring input,

or output of an output cam, and can also be inverted. The SCOUT engineering software is

used for parameterization.
●

Each channel can be parameterized as a digital input (DI) or digital output (DO).

●

Each channel can be parameterized as an input of a measuring input.

●

Each input of a measuring input has a selectable edge detection (falling edge, rising

edge, or both edges).

●

Each channel can be parameterized as an output of an output cam.

Содержание SIMOTION TM15




































































































Результаты поиска

Содержание SIMOTION TM15

Отзывы:

Бренды по названию

Популярные бренды

Siemens SIMOTION TM15, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание SIMOTION TM15

Отзывы:

Бренды по названию

Популярные бренды