Siemens SIMOTION TB30 Скачать руководство пользователя страница 95

Страница: 95 / 150

Supplementary system components

6.2 Fan/battery module

SIMOTION D4x5-2
Manual, 02/2012

6.2.2

Installing the fan/battery module

Overview

The procedure for installing the double fan/battery module is described below.

Procedure
There are cutouts on the lower side of the control unit to attach the module. Proceed as

follows to install the double fan/battery module:
1.

If required, insert a battery in the double fan/battery module.

Hold the double fan/battery module at an angle to the front with the open side facing up.

The battery must be visible.

Push the plastic lug into the slot-like cutout on the lower side of the control unit.

Tilt the double fan/battery module up until the two latches snap into place at the front.

Note the two contact strips that are lead through cutouts of the control unit.
This establishes the electrical connection between the double fan/battery module and the

control unit.

&RQWDFWVWULS

3ODVWLFOXJ

*XLGHOXJV

'RXEOHIDQEDWWHU\
PRGXOH

/DWFK

'RXEOHIDQEDWWHU\
PRGXOHPRXQWHG

Figure 6-2

Installing the double fan/battery module

Содержание SIMOTION TB30























































































































































Результаты поиска

Содержание SIMOTION TB30

Отзывы:

Похожие инструкции для SIMOTION TB30

Бренды по названию

Популярные бренды

Siemens SIMOTION TB30, Руководство пользователя

Результаты поиска

Содержание SIMOTION TB30

Отзывы:

Похожие инструкции для SIMOTION TB30

Бренды по названию

Популярные бренды