Siemens SIMOTION TB30 Скачать руководство пользователя страница 64

Страница: 64 / 150

Interfaces

3.6 Power supply

SIMOTION D4x5-2

Manual, 02/2012

3.6

Power supply

This interface is provided for connection of the external power supply.

Note
When using external power supplies (e.g. SITOP), the ground potential must be connected

with the protective ground terminal (PELV).

Characteristics of the interface

Table 3- 14 Interface X124

Characteristics

Type

Connector type

Combicon

Connection possibility

Up to 2.5 mm

Max. current carrying capacity incl. loop-through 20 A
Max. cable length

10 m

Interface assignment

Table 3- 15 Power supply X124

Signal name

Meaning

24 V power supply

Ground

Note
The 24 V is looped through via the 24 V connector. In this case, pin 1 is jumpered with pin 2,

and pin 3 is jumpered with pin 4 in the connector. The maximum current can be limited

through the current carrying capacity of the cable. The current carrying capacity of the cable

depends, for example, on the type of cable installation (cable duct, laying on a cable

rack, etc.).

Содержание SIMOTION TB30























































































































































Результаты поиска

Содержание SIMOTION TB30

Отзывы:

Похожие инструкции для SIMOTION TB30

Бренды по названию

Популярные бренды

Siemens SIMOTION TB30, Руководство пользователя

Результаты поиска

Содержание SIMOTION TB30

Отзывы:

Похожие инструкции для SIMOTION TB30

Бренды по названию

Популярные бренды