Siemens SIMOTION TB30 Скачать руководство пользователя страница 55

Страница: 55 / 150

Interfaces

3.4 PROFINET IO interface (only for SIMOTION D4x5-2 DP/PN)

SIMOTION D4x5-2
Manual, 02/2012

3.4

PROFINET IO interface (only for SIMOTION D4x5-2 DP/PN)

PROFINET is an open component-based industrial communication system using Ethernet

for distributed automation systems.
SIMOTION D4x5-2 DP/PN has a PROFINET interface with three ports (X150 P1-P3)

onboard. The PROFINET interface supports operation of a SIMOTION D4x5-2 DP/PN as an

IO controller and/or as an I device.

Interface position

The following figure contains information on the PROFINET interface of the control unit.

Position of the interface, labeling of the ports and the associated displays are described.

'LVSOD\

6WDWXV

JUHHQ

2II

\HOORZ

2II

0HDQLQJ

7UDQVIHUUDWHRUb0ELWV

1RRUIDXOW\FRQQHFWLRQ

'DWDH[FKDQJH

1RGDWDH[FKDQJH

'LVSOD\

6WDWXVRIWKHLQWHUIDFH31

6\QFKURQL]DWLRQVWDWXVRIWKHLQWHUIDFH6<

/('GLVSOD\VIRUWKHVWDWXVRILQWHUIDFH;

/,1.

$&7

/,1.

Figure 3-4

The position of the PROFINET X150 P1 to P3 interfaces and their displays (SIMOTION D445-2 DP/PN)

Note
The 3rd port of the PROFINET IO interface X150 P3 is also designated as X120 PN/IE OP.

This designation is not relevant for SIMOTION D.

Содержание SIMOTION TB30























































































































































Результаты поиска

Содержание SIMOTION TB30

Отзывы:

Похожие инструкции для SIMOTION TB30

Бренды по названию

Популярные бренды

Siemens SIMOTION TB30, Руководство пользователя

Результаты поиска

Содержание SIMOTION TB30

Отзывы:

Похожие инструкции для SIMOTION TB30

Бренды по названию

Популярные бренды