Siemens SIMOTION P320-4 E Скачать руководство пользователя

Страница: 109 / 166

6.3

Installation notes

Note the following:
● The SIMOTION P320-4 is approved for operation in closed rooms only.
● For installation in a control cabinet, observe the SIMATIC installation guidelines and

applicable DIN/VDE requirements or other applicable country-specific regulations.

● When the device is used in the area of Industrial Control Equipment according to UL508,

note that the device is classified as "Open Type". The installation of the device in a housing

according to UL508 is therefore a mandatory requirement for approval or operation in

according to UL508.

Securely fastening the SIMOTION P320-4

NOTICE
Insufficient load carrying capacity
If the wall it is mounted on does not have a sufficient load-bearing capacity, the device may

fall and be damaged.
Ensure that the mounting surface on the wall can bear four times the total weight of the device,

including fixing elements.

NOTICE
Incorrect fixing elements
The device may not be securely fitted if you use dowels and screws other than those specified

below for mounting. The device can fall and may be damaged.
Use only the dowels and screws specified in the following table.

Installation/mounting
6.3 Installation notes

SIMOTION P320-4 E / P320-4 S

Manual, 03/2018, A5E36004933B

109

Содержание SIMOTION P320-4 E







































































































































































Результаты поиска

Содержание SIMOTION P320-4 E

Отзывы:

Похожие инструкции для SIMOTION P320-4 E

Бренды по названию

Популярные бренды

Siemens SIMOTION P320-4 E, Руководство пользователя

Результаты поиска

Содержание SIMOTION P320-4 E

Отзывы:

Похожие инструкции для SIMOTION P320-4 E

Бренды по названию

Популярные бренды