Siemens SIMOTION P320-4 E Скачать руководство пользователя страница 99 | Manualshive

Страница: 99 / 222

Siemens SIMOTION P320-4 E Скачать руководство пользователя страница 99

Connection

6

6.1

Connection requirements

In this section it is described how the components of SIMOTION P320-4 are connected and

the elements for communication prepared.
During the installation of SIMOTION modules, you must pay attention to the electrical

configuration design.
You obtain information on wiring and networking a complete SIMOTION system.

Requirement

The SIMOTION P320-4 is already installed in a cabinet or in a controller housing.

Open equipment

These modules are open equipment. Therefore, only install modules in housings, cabinets, or

in electrical equipment rooms that can only be entered or accessed with a key or tool. Only

instructed or authorized personnel have access.
Observe the following points during installation:
● The device may only be connected to 24 VDC power supplies that meet the requirements

in accordance with SELV. The cable cross-section must be chosen large enough to ensure

that no damage can result from cable overheating in the event of a short-circuit in the

SIMOTION P320‑4.

● Protect the device against dust, moisture, heat and severe vibration.
● Do not subject the SIMOTION P320-4 to direct sunlight.
● Install the device in such a way that it cannot present a hazard (e.g. by toppling).
● Ensure that the clearance to other components or the sides of cabinets is at least 50 mm

above and 100 mm below the device.

SIMOTION P320-4 E / P320-4 S

Commissioning and Hardware Installation Manual, 11/2016

99

«
...
97
98
99
100
101
...
»

Содержание SIMOTION P320-4 E































































































































































































































Отзывы:

Нет отзывов