Siemens SIMOTION P320-4 E Скачать руководство пользователя страница 140

Страница: 140 / 222

Observe uniform configuration

Check if the offline configuration set via SIMOTION SCOUT (HW Config) corresponds exactly

to the online configuration set in the Station Configurator :

Figure 9-11 Illustration of the offline HW Config (left) - online Station Configurator (right)

9.5

Ethernet communication

9.5.1

Ethernet communication overview

SIMOTION P320-4 has one onboard Ethernet interface.

NOTICE
SIMOTION P Runtime
During SIMOTION P Runtime, the onboard Ethernet interface must be activated under

Windows.
The onboard Ethernet interface must not be deactivated or activated during operation.

You can connect Industrial Ethernet to the Ethernet interface X1.
Industrial Ethernet is a communication network with a transmission rate of 10/100/1000 Mbps.

Parameter assignment/addressing
9.5 Ethernet communication

SIMOTION P320-4 E / P320-4 S

140

Commissioning and Hardware Installation Manual, 11/2016

Содержание SIMOTION P320-4 E































































































































































































































Результаты поиска

Содержание SIMOTION P320-4 E

Отзывы:

Похожие инструкции для SIMOTION P320-4 E

Бренды по названию

Популярные бренды

Siemens SIMOTION P320-4 E, Руководство по вводу в эксплуатацию и установке оборудования

Результаты поиска

Содержание SIMOTION P320-4 E

Отзывы:

Похожие инструкции для SIMOTION P320-4 E

Бренды по названию

Популярные бренды