Siemens SIMOTION P320-3 Скачать руководство пользователя страница 80

Страница: 80 / 150

Installing/Mounting

5.2 Installing/removing an accessible CompactFlash card

SIMOTION P320-3 and Panel Fronts

Manual, 02/2012

5.2

Installing/removing an accessible CompactFlash card

Memory expansion options

The device features an accessible slot for CompactFlash cards (types I / II).
Only use SIMATIC PC CompactFlash cards for industrial application.

CAUTION

Replace the CompactFlash card only with a card of the same product version.
Only SIMATIC PC CompactFlash cards with product version 02 (ES 02) can be used for

this device.

Figure 5-1

SIMATIC PC CompactFlash

Figure 5-2

SIMATIC PC CompactFlash 4 GB - rear side with product version ES 02

Preparation

CAUTION

Data loss is possible on the CompactFlash card
Insertion/withdrawal of the CompactFlash card (CF card) while the device is switched on

can result in data loss on the CF card.
Exit the running software applications via the menu Start > Shut down, switch the device off

via the ON/OFF switch and disconnect the device from the power supply.

Содержание SIMOTION P320-3























































































































































Результаты поиска

Содержание SIMOTION P320-3

Отзывы:

Бренды по названию

Популярные бренды

Siemens SIMOTION P320-3, Руководство пользователя

Результаты поиска

Содержание SIMOTION P320-3

Отзывы:

Бренды по названию

Популярные бренды