Siemens SIMOTICS S-1FK2 Скачать руководство пользователя страница 89 | Manualshive

Страница: 89 / 768

Siemens SIMOTICS S-1FK2 Скачать руководство пользователя страница 89

5.3

Installing the converter

5.3.1

Installation conditions

When installing the converter carefully observe the conditions listed below in order to

guarantee reliable, continuous and trouble-free operation.
● The converter is designed for installation in a control cabinet.
● The converter is certified for use in environments with degree of pollution 2 without

condensation; i.e. in environments where no conductive pollution/dirt occurs. Condensation

is not permissible.

● The converter fulfills degree of protection IP20.
● EMC-compliant installation:

EMC-compliant installation of a machine or system (Page 35).

Additional requirements for plants and systems in the United States / Canada (UL/cUL)

A label with the following number is provided with the device: A5E36790112.
Note the instructions on the label and attach the label in a clearly visible location close to the

converter in the control cabinet.

Installation notes

● Install the converter vertically with the flap for the LED display facing upwards.

Figure 5-2

Mounting position of the converter

● Maintain the minimum clearances to other components.
● Use the recommended hardware (screws M5) and comply with the specified torques.

Installing

5.3 Installing the converter

SINAMICS S210 servo drive system

Operating Instructions, 12/2017, A5E41702836B AA

87

«
...
87
88
89
90
91
...
»

Содержание SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды