Siemens SIMOTICS S-1FK2 Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 768

Siemens SIMOTICS S-1FK2 Скачать руководство пользователя страница 63

4.2.2

Safe Brake Control (SBC)

Overview

672

6%&

v

t

The "Safe Brake Control" function (SBC) is

used to safely control the motor-integrated

holding brake.
The holding brake opens as soon as voltage is

available - and closes when in the no-voltage

state.

Functional features

In order that SBC can become active you must enable the function when commissioning the

system.

Note
SBC cannot be selected as an autonomous function; however, if it is enabled, it is activated

at the same time that STO is selected.

The holding brake is controlled using the encoder integrated in the motor.

Applications

SBC can be used wherever a safe position must be maintained even with a de-energized

motor, in order to prevent suspended or passing loads from dropping (e.g. lifting gear,

passenger elevators, winders). No external logic or switching elements required, as the

functionality is completely integrated in the drive.

Note
Condition of the motor holding brake
SBC is not able to identify as to whether a holding brake is mechanically worn or is a defective.
As a consequence, observe the maximum permissible number of emergency braking

operations for the motor holding brake being used.

Safety functions integrated in the drive

4.2 Basic Functions

SINAMICS S210 servo drive system

Operating Instructions, 12/2017, A5E41702836B AA

61

«
...
61
62
63
64
65
...
»

Содержание SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды